paver max

[windsordog]

Just wondering if anyone else that has a paver max has trouble with the head in the fall with the temp. changes ( as in spring tension) .is there any hints to what to look for , to speed up time in reworking the head or is it just one of those things. Also i would like to add this is a very nice forum i hope allot of people take advantage of it. I hope there will be allot of discussions in the future.( even from the paverboss) just kidding Jones.

[Glenn W]

How old is your Paver Max? You mention "spring tension" but the only springs on the Paver Max clamp are in the connection between the boom and the clamp (temp should have no noticeable affect on it). The Paver Max clamp is hydraulic and will be affected by cold temps to the extent that the hyd. fluid doesn't flow as well when cold. Allow for "warm-up" during cold mornings and that should solve your problems (cycle through all hydraulic functions a number of times to warm-up hyd fluid).

[windsordog]

I should have worded that better( my bad) i was refering to the steel teeth that touch the pavers .

[fredflnstn]

Windsordog, how many square feet can you lay in one day w/ the paver max and a mech. screed?

[Glenn W]

I should have worded that better( my bad) i was refering to the steel teeth that touch the pavers .

Hey Windordog...you still out there or did you give up on this forum? Sorry it took so long to reply but maybe I can help with the problem you were having with the steel teeth on the PaverMAX:
Try cutting a slot in each tooth. Don't cut it in half, just add a slot. We've been doing this recently and it seems to improve things.

[windsordog]

Thanks Glen we will try this. No I have not given up. YET. But it seems not much happens on here.

[Admin]

The activity level has definitly increased in the last few months. Thank you for everyones participation. We are continually working to improve The Hardscape Forum. Tell all your friends to join! The more the word gets out there, the more the site will continue to grow! Feel free to send your ideas on improving the Forum to admin@thehardscapeforum.com.

[Glenn W]

Windsordog, how many square feet can you lay in one day w/ the paver max and a mech. screed?

The typical production rate for (1) PaverMAX is 5,000 to 10,000 sq.ft. per 8-hour day for an experienced crew of about 6. For those new to mechanical installation, your crew should reach a 4,000 to 5,000 sq.ft. level within a relatively short period of time, maybe 1 week; some might take longer.

LEADERSHIP, SKILL and MOTIVATION will determine your success.

Most crews tend to hit a plateau at about the 5,000 sq.ft. level. Then after months of experience, higher production rates tend to occur.

Variables that affect all construction projects will determine if you achieve 5,000 (maybe less) or 10,000 (or more) sq. ft. on any given day. We have experienced occasional days with production of 12,000 to 15,000 sq.ft. Such production represents rare days that are difficult to achieve regularly. We've also experienced jobs where 3,000 sq.ft. was the daily average. These lower production rates typically represent jobs with unique and difficult conditions.

Just remember that meaningful production must include more than simply laying pavers. Also include: adjusting bond lines, inspecting & replacing pavers, cutting edge pavers, spreading and sweeping joint material, compaction and clean up – in other words: complete installation, anything else is irrelevant.

Also understand that proper ICPI installation practices must be followed. Cheating on quality only to achieve a higher production rate will lead to a failed project and lost profits.

To summarize: The machine is just as fast as your crews’ ability to operate it, supply it and keep pace with it. So don't worry about the machine keeping pace with your crew - figure out how you're going to get your crew to keep pace with the machine!!

[kelvinjona]

How old is your Paver Max? You mention "spring tension" but the only springs on the Paver Max clamp are in the connection between the boom and the clamp (temp should have no noticeable affect on it). The Paver Max clamp is hydraulic and will be affected by cold temps to the extent that the hyd. fluid doesn't flow as well when cold. Allow for "warm-up" during cold mornings and that should solve your problems (cycle through all hydraulic functions a number of times to warm-up hyd fluid).

Hi
Actually wats the features of this paver max? tell me in detail..
Thanks in advance...

[Glenn W]

In short, the PaverMAX is a unique machine designed & built specifically to install segmental pavers as efficiently as possible. Because it is unique, you really need to see one to appreciate it. But for now a list of some of the features includes:
- Kubota Diesel Engine
- Advanced hydraulic paver clamp
- Low maintenance costs and easy to service
- Low center of gravity, very stable even at high speed
- exceptional maneuverability
- excellent operator visibility
- etc

The most important features are the high quality design & construction which translate into supperior productivity and unmatched reliability.

If anyone has other questions or comments, please feel free to add them.